Qualcomm OBDII J1708 Instrukcja Naprawy Strona 18
- Strona / 110
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Securing the VTM50 Vehicle Telematics Module 50 (VTM50) Installation
4-2 80-JB566-1 Rev. C
MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION
Securing the VTM50
Use provided Dual Lock tape or self-drilling screws to mount and secure the VTM to a solid
surface within the dash.
Using Dual Lock Tape (Used for most installations)
1. Separate the two sides of the Dual Lock tape.
2. Clean the back of the VTM with the provided alcohol wipe and let dry. Once dried,
adhere one side of the Dual Lock tape. Apply firm pressure to set the tape.
3. Clean the mounting surface thoroughly, let dry, and then adhere the other side of the
Dual Lock tape. Apply firm pressure to set the tape.
4. Attach the VTM to the mounting location ensuring the locking hooks of the tape are fully
mated.
If the VTM will need to be moved to connect cables, be careful not to disturb the
adhesive side of the tape. Another option is to not press the locking hooks together until
after all the cable connectors have been attached to the VTM.
After application, the bond strength will increase as adhesive flows onto the surface. At
room temperature, approximately 50% of the ultimate strength will be achieved after 20
minutes.
When applied properly and had time to set, the VTM can be removed and reconnected
using the tape’s locking hooks while the tape remains adhered to the VTM and the
mounting surface.
Using Self-Drilling Screws
1. Verify there is not anything behind the mounting surface that may be damaged.
2. Two self-drilling screws are typically used to mount the VTM. Apply the screws through
the VTM’s eyelets at opposite diagonal corners.
- Installation and 1
- Troubleshooting 1
- QUALCOMM Incorporated 2
- 5775 Morehouse Drive 2
- San Diego, CA 92121-1714 2
- Installation Contents 3
- iv 80-JB566-1 Rev. C 4
- Important Safety Information 5
- Component Overview 7
- Display Holster 8
- RAM Mount 8
- Backing Plate 8
- Activation 9
- Online Activation Activation 10
- 2-2 80-JB566-1 Rev. C 10
- 80-JB566-1 Rev. C 2-3 11
- Activation Online Activation 11
- Application Management 12
- 80-JB566-1 Rev. C 2-5 13
- 2-6 80-JB566-1 Rev. C 14
- Installation Planning 15
- Installing the VTM50 17
- Securing the VTM50 18
- Using Self-Drilling Screws 18
- Antenna Installation 19
- Installing Antenna 20
- Selecting a Mounting Location 21
- Installing the Display 22
- Power/IO Cable Connection 25
- Extending MCP50 Ignition Wire 26
- Optional Accessories 27
- PTO Installation 28
- System Verification 31
- 9-4 80-JB566-1 Rev. C 34
- Troubleshooting Contents 35
- 80-JB566-1 Rev. C 36
- Troubleshooting Guidelines 37
- Replace Only Faulty Parts 38
- 08AAA_05 40
- 80-JB566-1 Rev. C 11-3 41
- (-) lead on Pin A 41
- (+) lead on Pin B 41
- 11-4 80-JB566-1 Rev. C 42
- DIU Problems 43
- Cannot Send Messages 45
- 13-2 80-JB566-1 Rev. C 46
- Cellular End to End Problems 47
- 14-2 80-JB566-1 Rev. C 48
- CDD Database Sync Problem 51
- 16-2 80-JB566-1 Rev. C 52
- GPS Fix Problem 53
- 18-2 80-JB566-1 Rev. C 56
- 19-2 80-JB566-1 Rev. C 58
- Ignition On Detection Problem 59
- 20-2 80-JB566-1 Rev. C 60
- Core Data Problem 61
- VTM LED Indicator 63
- 22-2 80-JB566-1 Rev. C 64
- Acquiring Network Problem 65
- System Overview 67
- Normal Performance 67
- - - - - - - - - - 69
- 24-4 80-JB566-1 Rev. C 70
- Overview 71
- Abnormal Performance 71
- Event Not Triggered 72
- 80-JB566-1 Rev. C 25-3 73
- Events Triggered in Error 74
- 80-JB566-1 Rev. C 26-1 75
- 26-2 80-JB566-1 Rev. C 76
- Appendix Contents 77
- Wiring Diagrams and Charts 79
- 6-Pin Power/IO Cable 80
- 9-Pin Power/IO Cable 80
- 08AAA_051 83
- A-6 80-JB566-1 Rev. C 84
- B-2 80-JB566-1 Rev. C 86
- 1/4" 88
- 03AAA_270a 88
- Butt Splicing 89
- 03AAA_90b 90
- Crimp tooth 90
- Do NOT crimp wire here 90
- Crimp here 90
- Crimping Tool 91
- Ring Terminals 92
- Proper Grounding 93
- Routing and Protecting Cables 94
- Standard RMA Procedure 95
- D-2 80-JB566-1 Rev. C 96
- Before You Start 97
- E-6 80-JB566-1 Rev. C 102
- Inspecting the Antenna 104
- Component Information 105
- 45-JB593-1 107
- 80-JB566-1 Rev. C G-3 107
- Paccar adapter 107
- G-4 80-JB566-1 Rev. C 108
- Installation Form 109
- H-2 80-JB566-1 Rev. C 110
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji